当前位置: 电脑软硬件应用网 > 电脑学院 > 局域网技术 > 正文 |
|
|||
路由器配置命令(汇总) | |||
2006-9-16 9:32:44 文/45itcom收集 出处:电脑软硬件应用网 | |||
Cisco路由配置语句汇总 启动接口,分配IP地址: router> router> enable router# router# configure terminal router(config)# router(config-if)# no shutdown router(config-if)# ip address IP-Address Subnet-Mask router(config-if)# ^z
router(config)# router rip router(config-if)# network Network-Number <--通告标准A,B,C类网--> router(config-if)# ^z
router(config)# router igrp AS-Number <-- AS-Number范围1~65535--> router(config-if)# network Network-Number <--通告标准A,B,C类网--> router(config-if)# ^z router(config)# ipx routing [node address] router(config)# ipx maximum-paths Paths <--设置负载平衡,范围1~512--> router(config)# interface Type Port router(config-if)# ipx network Network-Number [encapsulation encapsulation-type] [secondary] <--通告标准A,B,C类网--> router(config-if)# ^z
router(config)# dialer-list Group-Number protocol Protocol-Type permit [list ACL-Number] router(config)# interface bri 0 router(config-if)# dialer-group Group-Number router(config-if)# dialer map Protocol-Type Next-Hop-Address name Hostname Telphone-Number router(config-if)# ^z
router(config)# isdnth-typeth-Type <--配置ISDN交换机类型,中国使用basic-net3--> router(config-if)# ^z
router(config-if)# encapsulation frame-relay [cisco | ietf ] router(config-if)# frame-relay lmi-type [ansi | cisco | q933a ] router(config-if)# bandwidth kilobits router(config-if)# frame-relay invers-arp [ Protocol ] [dlci ] <--配置静态Invers ARP表: router(config)# frame-relay Protocol Protocol-Address DLCI [ Broadcast ] [ ietf | cisco ] [ payload-compress | packet-by-packet ] --> <--设置Keepalive间隔: router(config-if)# keepalive Number --> <--为本地接口指定DLCI: router(config-if)# frame-lelay local-dlci Number --> <--子接口配置: router(config-if)# interface Type Port.Subininterface-Number [ multipoint | point-to-point ] router(config-subif)# ip unnumbered Interface router(config-subif)# frame-lelay local-dlci Number --> router(config-if)# ^z
router(config)# access-list Access-List-Number [ permit | deny ] source [ source-mask ] <-- Access-List-Number 范围:1~99标准ACL;100~199扩展ACL;800~899标准IPX ACL;900~999扩展IPX ACL;1000~1099 IPX SAP ACL;600~699Apple Talk ACL--> router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z
router(config)# access-list Access-List-Number [ permit | deny ] [ Protocol | Protocol-Number ] source source-wildcard [ Source-Port ] destination destination-wildcard [ Destination-Port ] [ established ] router(config)# interface Type Port router(config-if)# ip access-group Access-List-Number [ in | out ] router(config-if)# ^z
router(config)# ip access-list [ standard | extended ] ACL-Name router(config [ std- | ext- ] nacl)# [ permit | deny ] [ IP-Access-List-Test-Conditions ] router(config [ std- | ext- ] nacl)# no [ permit | deny ] [ IP-Access-List-Test-Conditions ] router(config [ std- | ext- ] nacl)# ^z router(config)# interface Type Port router(config-if)# ip access-group [ACL-Name | 1~199 ] [ in | out ] 配置DCE时钟: router# show controllers Type Port <--确定DCE接口--> router(confin-if)# clock rate 64000 <--进入DCE接口设置时钟速率--> router(config-if)# ^z 配置PPP协议: router(config)# username Name password Set-Password-Here <--验证方建立数据库--> router(config)# interface Type Port router(config-if)# encapsulation ppp <--启动PPP协议--> router(config-if)# ppp outhentication [ chap | chap pap | pap chap | pap ] <--选择PPP认证--> router(config-if)# ppp pap sent-username Name password Password <--发送验证信息--> router(config-if)# ^z
验证方: router-server(config)# username Client password 12345 <--验证方建立数据库--> router-server(config)# interface serial 0 router-server(config-if)# encapsulation ppp router-server(config-if)# ppp authentication pap <--选择使用PAP实现PPP认证--> router-server(config-if)# ^z 被验证方: router-client(config-if)# encapsulation ppp router-client(config-if)# ppp pap sent-username Client password 12345 <--发送验证信息--> router-client(config-if)# ^z PAP双向认证配置实例: 路由器 A: routerA(config)# username B password 12345 routerA(config)# interface serial 0 routerA(config-if)# encapsulation ppp routerA(config-if)# ppp authentication pap routerA(config-if)# ppp pap sent-username A password 54321 routerA(config-if)# ^z 路由器 B: routerB(config)# username A password 54321 routerB(config)# interface serial 1 routerB(config-if)# encapsulation ppp routerB(config-if)# ppp authentication pap routerB(config-if)# ppp pap sent-username B password 12345 routerB(config-if)# ^z CHAP单向认证配置实例: 验证方: router-server(config)# username router-client password 12345 router-server(config)# interface serial 0 router-server(config-if)# encapsulation ppp router-server(config-if)# ppp authentication chap router-server(config-if)# ^z 被验证方: router-client(config-if)# encapsulation ppp router-client(config-if)# ppp authentication chap router-client(config-if)# ppp chap hostname router-client router-client(config-if)# ppp chap password 12345 router-client(config-if)# ^z 路由器 A: routerA(config)# username routerB password 12345 routerA(config)# interface serial 0 routerA(config-if)# encapsulation ppp routerA(config-if)# ppp authentication chap routerA(config-if)# ppp chap hostname routerA routerA(config-if)# ppp chap password 54321 routerA(config-if)# ^z 路由器 B: routerB(config)# username routerA password 54321 routerB(config)# interface serial 1 routerB(config-if)# encapsulation ppp routerB(config-if)# ppp authentication chap routerB(config-if)# ppp chap hostname routerB routerB(config-if)# ppp chap password 12345 routerB(config-if)# ^z Telnet使用: routerA# terminal monitor <--可以传回在远端主机执行Debug命令的结果--> routerA# telnet IP-Address [ Router-Name ] <--Telnet到指定的地址或名字的主机--> routerB# [ exit | logout ] <--退出Telnet--> routerB# ++<6>再按 <--挂起Telnet--> routerA# show sessions <--显示当前所有Telnet的信息,包括Connect-Number --> routerA# Connect-Number <--返回指定的Telnet连接--> routerA# disconnect IP-Address [ Router-Name ] <--断开指定地址或名字的主机的连接--> routerA# show user <--显示Telnet到本机的连接信息--> routerA# clear line [ 0 | 1 | 2 | 3 | 4 ] <--断开指定Telnet到本机的连接-->
router(config)# line vty 0 4 router(config-line)# access-class ACL-Number router(config)# ^z
router(config)# hostname Set-Hostname router(config)# ^z router(config)# ^z 设置用户模式密码: router(config)# line console 0 router(config-line)# login router(config-line)# password Set-Password router(config-line)# ^z 设置Telnet密码: router(config)# line vty 0 4 router(config-line)# login router(config-line)# password Set-Password router(config-line)# ^z
router(config)# enable password Set-Password <--不加密的密码,明码--> router(config)# enable secret Set-Password <--经过加密的密码--> router(config)# ^z 给所有密码加密: router(config)# service password-ancryption Set-Password-Here router(config)# no service password-ancryption <--取消加密--> router(config)# ^z 设置登录Banner: router(config)# banner motd 分隔符 Set-Banner-InFORMation-Here 分隔符 <--前后分隔符一定要一致-->
router(config-if)# description Set-Port-InFORMation-Here router(config)# ^z
router(config-if)# cdp enable <--在指定端口启用CDP,缺省--> router(config-if)# no cdp enable <--在指定端口关闭CDP--> router(config)# cdp run <--使所有端口启用CDP--> router(config)# no cdp run <--使所有端口关闭CDP-->
router# ping IP-Address router# ping <--扩展Ping命令--> Protocol [ip]:[ Protocol-Type ] <--选择协议类型--> Target IP address:IP-Address <--输入测试地址--> Repeat count [5]: <--选择发送的ICMP包数量--> Datagram size [100]: <--选择每个包的大小--> Timeout in seconds [2]: <--设置每个包的超时时间--> Extended commands [n]:y <--使用扩展Ping命令--> Sweep range of sizes [n]: Tra |
|||
最新热点 | 最新推荐 | 相关阅读 | ||
路由器当交换机用注意事项 剖析阿尔法路由器说明书:如何注销本 华为SmartAX MT800的路由配置方法 恢复路由器出厂设置时的密码 优化cisco路由器 封锁须要的处事 换路由器后电脑网速变慢了 路由器To路由器:双路由器连接设置 新手知识:路由器组网特点详述 如何保护你的路由器密码? 知识:五大方面诠释路由器分类 |
关于45IT | About 45IT | 联系方式 | 版权声明 | 网站导航 | |
Copyright © 2003-2011 45IT. All Rights Reserved 浙ICP备09049068号 |